LED Power Supply – 1000W 24V Ultra High Power Mean Well LRS-1000-24 Compatible

1000W Ultra High-Power Enclosed Supply — Mean Well LRS-1000-24 Drop-In Match

Few power supplies on the market deliver a full kilowatt of 24V DC output in a package small enough to mount inside a standard luminaire housing. This BrightLink LRS-1000-compatible driver does exactly that, offering an output of 41.7A at 24V from a chassis measuring just 215 x 115 x 30mm. Whether you are feeding a 10-meter run of high-density LED strip, powering a bank of horticulture fixtures, or centralizing DC distribution for an entire floor of commercial lighting, this single module replaces the clutter and failure points of multiple smaller units.

Performance Highlights

• 1000W in an Industry-Standard Footprint — The 215 x 115 x 30mm envelope matches the LRS-1000 form factor exactly, fitting the same mounting holes and leaving room for standard M4 hardware. No panel modification needed when retrofitting from Mean Well.
• 41.7A at 24V DC — Enough current headroom to drive long LED strip runs (up to 10 meters of 14.4W/m strip) without visible voltage drop at the far end, or to power 40+ individual 24V LED modules in parallel.
• 90%+ Efficiency with Active PFC — Minimizes energy waste and heat generation inside enclosed spaces. The built-in PFC circuit maintains a power factor above 0.95, meeting IEC 61000-3-2 Class A limits for commercial installations.
• Built-in Fan with Thermal Management — A temperature-controlled internal fan maintains full output up to 70C ambient. The fan speed ramps automatically, staying quiet under normal loads and ramping up only when thermal headroom shrinks.
• Five-Layer Protection System — Short-circuit, over-current, over-voltage, over-temperature, and under-voltage lockout work together to prevent cascading failures. All protections are auto-recovering: remove the fault and the supply resumes normal operation without a power cycle.
• Universal Input 90-264 VAC — Works worldwide on any single-phase mains supply from 90V to 264V AC, making it suitable for export-oriented equipment and multi-region deployments without SKU proliferation.

Technical Specifications

Built for Demanding Applications

• Commercial High-Bay & Low-Bay Lighting — Powers multiple 200W+ LED high-bay fixtures from a centralized 24V bus, reducing per-fixture driver costs and simplifying electrical maintenance in warehouses and gyms.
• LED Horticulture & Greenhouse Systems — Delivers the sustained high-current output that full-spectrum grow panels require during 16-18 hour daily photoperiods, with thermal management rated for ambient greenhouse temperatures up to 50C.
• Large-Area Architectural LED Installations — One unit drives up to 100 meters of 10W/m COB LED strip for facade lighting, perimeter illumination, or decorative ceiling coves in hospitality and retail environments.
• Event & Exhibition Temporary Lighting — Portable, lightweight, and compatible with generator power (wide input range), this supply is ideal for trade show booths, concert stages, and pop-up retail installations.
• DC Micro-Grid & Battery Backup Systems — Serves as the AC-to-DC front-end in 24V DC micro-grids paired with solar charge controllers and UPS battery banks for off-grid or backup-powered LED lighting.

Installation Tips

Mount horizontally or vertically using the four M4 mounting holes on the base plate. Maintain at least 30mm clearance above and below the unit for airflow. AC input uses a 3-position terminal block; DC output uses a 4-position block (multiple +V and -V pins for parallel wiring to reduce contact resistance). The built-in fan draws air from the side label — do not obstruct. For 440Hz aircraft or marine power, verify derating curves in the datasheet.

The BrightLink Commitment

Every 1000W unit undergoes a 4-hour full-load burn-in test at 50C ambient before leaving our ISO 9001 factory. You receive a serialized test certificate with each shipment, documenting output voltage accuracy, ripple measurement, and protection trip points. Our direct-from-factory value saves 35-50% compared to Mean Well retail cost, and our 5-year warranty covers parts and advance replacement. For OEM volumes above 100 units, we offer custom labeling, output voltage trimming, and conformal coating for harsh environments.